Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ40A Rebar Cutter proper use and safety precautio...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ40A Rebar Cutter proper use and safety precautio...: 1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece. 2. ...

GQ40A Rebar Cutter proper use and safety precautions

1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece.
2. Before starting, you should check to make sure no cracks GQ40A Rebar Cutter, turret bolt, solid shield. Then rotate the pulley by hand to check the gear meshing clearance, adjust the cutter gap.
3. After starting, you should first dry run, check after each transmission parts and bearings in normal operation only after the job.
4. machinery does not reach normal operating speed may not cut material. When cutting, use the cutter, the lower parts of the alignment edge grip reinforced quickly put, the operator should stand on the side of force to suppress the fixed blade steel, should be reinforced to prevent the end of the pop-up hurt. It is prohibited on both sides of the blade with both hands holding the steel sub-leaning feeding.
5. Do not cut diameter and strength than mechanical nameplate steel and red-hot steel. Once cut off when a plurality of reinforcement, the total cross-sectional area should be within the specified range.
6. Cut low-alloy steel, replace the high hardness cutter, GQ40A Rebar Cutter plate diameter should be consistent with the provisions.
7. When cutting short material, distance between the hand and the knife should be maintained at 150mm or more, such as hand side is less than 400mm, you should use short steel casing or jig head pinched or folder in prison.
8. The operation is prohibited by hand directly decapitation and remove debris near the cutter. Rebar cutter swing around and around, can not stay non-operators.
9. When they find machinery not functioning properly, abnormal noise or skew cutter, you should immediately downtime.
10. After the job, you should cut off the power, steel brush to remove debris between the cutter, carry out the whole cleaning lubrication.
11. A hydraulic drive front GQ40A Rebar Cutter operation, check that the hydraulic oil and motor rotation direction to meet the requirements. After starting, you should load operation, loose open valve, drain the body of the air cylinder net, before proceeding cut tendons.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: How GQ40A Rebar Cutter maintenance?

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: How GQ40A Rebar Cutter maintenance?: Any mechanical maintenance is very important,  GQ40A Rebar Cutter  confidential how to care for, I'm here to give you a brief introducti...

How GQ40A Rebar Cutter maintenance?

Any mechanical maintenance is very important, GQ40A Rebar Cutter confidential how to care for, I'm here to give you a brief introduction:
1. Turn on the machine carefully before a site inspection is normal, reliable connection bolts are tightened. Pipe leaks. A portion of the fastening bolts should regularly check for loose with a wrench.
2.GQ40A Rebar Cutter parts need to be lubricated regularly add oil.
3. Replace the cutter or repair machinery, turn off the power, hung overhaul cards.
4. timely liquidation mechanical hygiene, keeping equipment clean.
5. Turn off the power to work, turn off gas supply
Real customer satisfaction, GQ40A Rebar Cutter welcome to all walks of life come to visit, study, discuss business, welcome you soon!

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: C42 Rebar Cutter infeed depth analysis section

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: C42 Rebar Cutter infeed depth analysis section:    As a specialized steel processing machinery, Yongyi Tongfeng C42 Rebar Cutter  not only ensures the processing quality, but also improve...

C42 Rebar Cutter infeed depth analysis section

   As a specialized steel processing machinery, Yongyi TongfengC42 Rebar Cutter not only ensures the processing quality, but also improve work efficiency, for construction work brought great convenience. Reinforced feed portion is an integral part bending hoop machine, if you want to understand their working mechanism, see below.
  C42 Rebar Cutter is usually in the form of disk storage. In Yongyi Tongfeng hoop bending machine, steel feed and straightening is accomplished simultaneously. Two drive wheels from the outside into the steel, and at the same time the level of alignment. Wherein the second set of drive wheels by Yongyi Tongfeng servo motor through an intermediate transmission mechanism, led directly to the first set of drive wheels between the drive wheels and the second group, are connected by a sprocket, a second set of drive wheels to rotate at the same time with the sprocket, C42 Rebar Cutter drive the first set of wheel rotation, so that you can implement the reinforced feed tasks.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine structure and working pri...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine structure and working pri...: Portable cutting machine  Construction: Vertical steel cutting machines for precast steel processing plant production line for stationary...

Portable cutting machine structure and working principle

Portable cutting machine

 Construction: Vertical steel cutting machines for precast steel processing plant production line for stationary use.
How it works: driven by an electric motor powered by the flier pair of pulleys, and then the third gear, and then drive the eccentric shaft by sliding key clutch,Portable Cutting Machine realized from the movement of the movable blade and the movable blade with cut reinforcement. The clutch is controlled by the handle out of its binding and manipulation of the up and down movement of the movable blade. Pressing device by hand wheel rotation, drive a reminder of an inner threaded screw up and down helical gears,Portable Cutting Machine clamping bars of different diameters.

Electro-hydraulic

Construction: electro-hydraulic steel cutting machine mainly consists of motor, hydraulic transmission, controls, fixed moving blades and other components.
How it works: The motor drives the eccentric shaft rotates, the eccentric shaft eccentric face dismissal and plunger reciprocated it touches, so that produce high-pressure piston pump oil into the cylinder body,Portable Cutting Machine push the piston within the cylinder, the movable blade driven forward, and fixed on a support fixed with the wrong blade and cut steel.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Process analysis portable cutting machine

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Process analysis portable cutting machine:     Process  Portable Cutting Machine  metal can be divided into the following phases: the elastic blade pressed into the metallic phase; p...

Process analysis portable cutting machine

    Process Portable Cutting Machine metal can be divided into the following phases: the elastic blade pressed into the metallic phase; plastic sheet is pressed into the metal phase; phase sliding metal and plastic; phases of crack initiation and propagation metal, metal phase of crack growth and unstable fracture. Generally it can be divided roughly into two phases; the blade is pressed in the sliding phase and metal phase metal plastic.

    At different stages within the region of shear it was reduced metal state is different. Throughout the process of Portable Cutting Machine, cutting voltage changing region, the cutting force is also constantly changing. Experimental results show that the maximum tangential force produced in the terminal phase sheet is pressed in, sliding metal Portable Cutting Machine plastic at the beginning of the stage, so that the cutting process can be divided into model overall strength in two stages to establish a shearing process.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Development team interested portable cutting machi...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Development team interested portable cutting machi...: They think there is much of   Portable Cutting Machine  people Yongyi Tongfeng are in our company understand, because of our propaganda to l...

Development team interested portable cutting machine

They think there is much of  Portable Cutting Machine people Yongyi Tongfeng are in our company understand, because of our propaganda to let more people know of the existence of a device of this type, which creates a lot of business opportunities for many people building materials makes competition more intense steel, and this competition is that we can greatly increase the quality and use of quality steel, which is the most customers is undoubtedly a very good thing.  Portable Cutting Machine to the benefits created by many people may not be very clear, this is a lot of want to invest in this equipment are still undecided, and the interests of this is also a very clear, given the current state of the building management seismic capability has become increasingly strict, so the proportion of the more reinforced construction downloaded growing, but the steel is to be processed in a variety of ways to use all parts of the building, so must be reinforced by our processing equipment Portable Cutting Machine, so now this is undoubtedly the best investment project in the team now, and the needs of initial capital investment of this project is not large, so most of my friends are also fully invested, so our awful portable cutting machine is definitely just want to see their interests.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable Cutting Machine should be cleaned

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable Cutting Machine should be cleaned: First, wash and clean-up. As a steel processing equipment, steel cutting machine using undoubtedly will leave some residual steel scrap, so ...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Master GQ40A Rebar Cutter maintenance points neces...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Master GQ40A Rebar Cutter maintenance points neces...: Maintenance points  GQ40A Rebar Cutter  equipment mainly in: Maintenance points a day after the work is completed, to develop promptly cl...

Master GQ40A Rebar Cutter maintenance points necessary

Maintenance points GQ40A Rebar Cutter equipment mainly in:

Maintenance points a day after the work is completed, to develop promptly clean up the habit of cutting machine tools, cutting tools around the same time to all kinds of debris piled up, one by one classify clean up and keep clean the entire cutting machine. At the same time, to use special tools for cutting machine all bolts and screws, reinforcement, tighten and stick cutting machine internal feed belt is loose? If so, to timely adjust. There is to check the prop wear, timely blunt tool replacement.

Maintenance Point # 2, when GQ40A Rebar Cutter used continuously over four hundred to five hundred hours, necessary and timely periodic maintenance of equipment. For example, add the oil, adjust the tool space, check the eccentricity of the bearing and gears and so on. Need to remind the operator to note that in winter, GQ40A Rebar Cutter ZG-2 is best to use oil. This type of lubricant relatively thin, more suitable for winter use; in summer, it is best to use the number ZG-4 grease. This type of lubricating oil more viscous, more suitable for summer use.

Portable Cutting Machine should be cleaned

First, wash and clean-up. As a steel processing equipment, steel cutting machine using undoubtedly will leave some residual steel scrap, so after using the need to develop a good habit, it is timely for the various machines are devices to clean up. So as not to be disturbed in the future use of the process. At the same time when the device is not used to carry out the necessary cleanup is particularly important, including the use of necessary damp cloth with neutral detergent to clean the surface of the device, remove stains and dirt on top of the machine, to avoid the prolonged impact of Portable Cutting Machine appearance and performance. In the clean-up time, especially for the interior of the machine and a number of blind spots clean.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check  Portable Cutting Machine is a regular process that requires a dedicated time to maintenance. The machine should be cleaned

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter:     The characteristic  GQ40A Rebar Cutter , which clearly shows us its automatic control at work, saving time and effort simply do not tell...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter:     The characteristic  GQ40A Rebar Cutter , which clearly shows us its automatic control at work, saving time and effort simply do not tell...

The interior design GQ40A Rebar Cutter

    The characteristic GQ40A Rebar Cutter, which clearly shows us its automatic control at work, saving time and effort simply do not tell the length of its press wheels do not need to enter the number of pulses, it's excellent performance is reflected in this When the automatic identification and automatic integration of professional work.
    In addition, the interior design can reach the safe operation of GQ40A Rebar Cutter, wherein the interior of the electrical board, more than a layer designed to prevent dust or the conductive material to achieve fall into the danger of accidents caused by accidental short circuit. And this machine does not need frequent repairs, even when the repair is also very convenient. Of course, it's another laudable feature is its output more than one point, the general GQ40A Rebar Cutter will be arranged to three, this advantage is capable of preventing an unexpected point of failure occurs, change to another point in time work .