Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ40A Rebar Cutter proper use and safety precautio...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ40A Rebar Cutter proper use and safety precautio...: 1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece. 2. ...

GQ40A Rebar Cutter proper use and safety precautions

1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece.
2. Before starting, you should check to make sure no cracks GQ40A Rebar Cutter, turret bolt, solid shield. Then rotate the pulley by hand to check the gear meshing clearance, adjust the cutter gap.
3. After starting, you should first dry run, check after each transmission parts and bearings in normal operation only after the job.
4. machinery does not reach normal operating speed may not cut material. When cutting, use the cutter, the lower parts of the alignment edge grip reinforced quickly put, the operator should stand on the side of force to suppress the fixed blade steel, should be reinforced to prevent the end of the pop-up hurt. It is prohibited on both sides of the blade with both hands holding the steel sub-leaning feeding.
5. Do not cut diameter and strength than mechanical nameplate steel and red-hot steel. Once cut off when a plurality of reinforcement, the total cross-sectional area should be within the specified range.
6. Cut low-alloy steel, replace the high hardness cutter, GQ40A Rebar Cutter plate diameter should be consistent with the provisions.
7. When cutting short material, distance between the hand and the knife should be maintained at 150mm or more, such as hand side is less than 400mm, you should use short steel casing or jig head pinched or folder in prison.
8. The operation is prohibited by hand directly decapitation and remove debris near the cutter. Rebar cutter swing around and around, can not stay non-operators.
9. When they find machinery not functioning properly, abnormal noise or skew cutter, you should immediately downtime.
10. After the job, you should cut off the power, steel brush to remove debris between the cutter, carry out the whole cleaning lubrication.
11. A hydraulic drive front GQ40A Rebar Cutter operation, check that the hydraulic oil and motor rotation direction to meet the requirements. After starting, you should load operation, loose open valve, drain the body of the air cylinder net, before proceeding cut tendons.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: How GQ40A Rebar Cutter maintenance?

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: How GQ40A Rebar Cutter maintenance?: Any mechanical maintenance is very important,  GQ40A Rebar Cutter  confidential how to care for, I'm here to give you a brief introducti...

How GQ40A Rebar Cutter maintenance?

Any mechanical maintenance is very important, GQ40A Rebar Cutter confidential how to care for, I'm here to give you a brief introduction:
1. Turn on the machine carefully before a site inspection is normal, reliable connection bolts are tightened. Pipe leaks. A portion of the fastening bolts should regularly check for loose with a wrench.
2.GQ40A Rebar Cutter parts need to be lubricated regularly add oil.
3. Replace the cutter or repair machinery, turn off the power, hung overhaul cards.
4. timely liquidation mechanical hygiene, keeping equipment clean.
5. Turn off the power to work, turn off gas supply
Real customer satisfaction, GQ40A Rebar Cutter welcome to all walks of life come to visit, study, discuss business, welcome you soon!

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: C42 Rebar Cutter infeed depth analysis section

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: C42 Rebar Cutter infeed depth analysis section:    As a specialized steel processing machinery, Yongyi Tongfeng C42 Rebar Cutter  not only ensures the processing quality, but also improve...

C42 Rebar Cutter infeed depth analysis section

   As a specialized steel processing machinery, Yongyi TongfengC42 Rebar Cutter not only ensures the processing quality, but also improve work efficiency, for construction work brought great convenience. Reinforced feed portion is an integral part bending hoop machine, if you want to understand their working mechanism, see below.
  C42 Rebar Cutter is usually in the form of disk storage. In Yongyi Tongfeng hoop bending machine, steel feed and straightening is accomplished simultaneously. Two drive wheels from the outside into the steel, and at the same time the level of alignment. Wherein the second set of drive wheels by Yongyi Tongfeng servo motor through an intermediate transmission mechanism, led directly to the first set of drive wheels between the drive wheels and the second group, are connected by a sprocket, a second set of drive wheels to rotate at the same time with the sprocket, C42 Rebar Cutter drive the first set of wheel rotation, so that you can implement the reinforced feed tasks.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine structure and working pri...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine structure and working pri...: Portable cutting machine  Construction: Vertical steel cutting machines for precast steel processing plant production line for stationary...

Portable cutting machine structure and working principle

Portable cutting machine

 Construction: Vertical steel cutting machines for precast steel processing plant production line for stationary use.
How it works: driven by an electric motor powered by the flier pair of pulleys, and then the third gear, and then drive the eccentric shaft by sliding key clutch,Portable Cutting Machine realized from the movement of the movable blade and the movable blade with cut reinforcement. The clutch is controlled by the handle out of its binding and manipulation of the up and down movement of the movable blade. Pressing device by hand wheel rotation, drive a reminder of an inner threaded screw up and down helical gears,Portable Cutting Machine clamping bars of different diameters.

Electro-hydraulic

Construction: electro-hydraulic steel cutting machine mainly consists of motor, hydraulic transmission, controls, fixed moving blades and other components.
How it works: The motor drives the eccentric shaft rotates, the eccentric shaft eccentric face dismissal and plunger reciprocated it touches, so that produce high-pressure piston pump oil into the cylinder body,Portable Cutting Machine push the piston within the cylinder, the movable blade driven forward, and fixed on a support fixed with the wrong blade and cut steel.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Process analysis portable cutting machine

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Process analysis portable cutting machine:     Process  Portable Cutting Machine  metal can be divided into the following phases: the elastic blade pressed into the metallic phase; p...

Process analysis portable cutting machine

    Process Portable Cutting Machine metal can be divided into the following phases: the elastic blade pressed into the metallic phase; plastic sheet is pressed into the metal phase; phase sliding metal and plastic; phases of crack initiation and propagation metal, metal phase of crack growth and unstable fracture. Generally it can be divided roughly into two phases; the blade is pressed in the sliding phase and metal phase metal plastic.

    At different stages within the region of shear it was reduced metal state is different. Throughout the process of Portable Cutting Machine, cutting voltage changing region, the cutting force is also constantly changing. Experimental results show that the maximum tangential force produced in the terminal phase sheet is pressed in, sliding metal Portable Cutting Machine plastic at the beginning of the stage, so that the cutting process can be divided into model overall strength in two stages to establish a shearing process.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Development team interested portable cutting machi...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Development team interested portable cutting machi...: They think there is much of   Portable Cutting Machine  people Yongyi Tongfeng are in our company understand, because of our propaganda to l...

Development team interested portable cutting machine

They think there is much of  Portable Cutting Machine people Yongyi Tongfeng are in our company understand, because of our propaganda to let more people know of the existence of a device of this type, which creates a lot of business opportunities for many people building materials makes competition more intense steel, and this competition is that we can greatly increase the quality and use of quality steel, which is the most customers is undoubtedly a very good thing.  Portable Cutting Machine to the benefits created by many people may not be very clear, this is a lot of want to invest in this equipment are still undecided, and the interests of this is also a very clear, given the current state of the building management seismic capability has become increasingly strict, so the proportion of the more reinforced construction downloaded growing, but the steel is to be processed in a variety of ways to use all parts of the building, so must be reinforced by our processing equipment Portable Cutting Machine, so now this is undoubtedly the best investment project in the team now, and the needs of initial capital investment of this project is not large, so most of my friends are also fully invested, so our awful portable cutting machine is definitely just want to see their interests.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable Cutting Machine should be cleaned

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable Cutting Machine should be cleaned: First, wash and clean-up. As a steel processing equipment, steel cutting machine using undoubtedly will leave some residual steel scrap, so ...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Master GQ40A Rebar Cutter maintenance points neces...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Master GQ40A Rebar Cutter maintenance points neces...: Maintenance points  GQ40A Rebar Cutter  equipment mainly in: Maintenance points a day after the work is completed, to develop promptly cl...

Master GQ40A Rebar Cutter maintenance points necessary

Maintenance points GQ40A Rebar Cutter equipment mainly in:

Maintenance points a day after the work is completed, to develop promptly clean up the habit of cutting machine tools, cutting tools around the same time to all kinds of debris piled up, one by one classify clean up and keep clean the entire cutting machine. At the same time, to use special tools for cutting machine all bolts and screws, reinforcement, tighten and stick cutting machine internal feed belt is loose? If so, to timely adjust. There is to check the prop wear, timely blunt tool replacement.

Maintenance Point # 2, when GQ40A Rebar Cutter used continuously over four hundred to five hundred hours, necessary and timely periodic maintenance of equipment. For example, add the oil, adjust the tool space, check the eccentricity of the bearing and gears and so on. Need to remind the operator to note that in winter, GQ40A Rebar Cutter ZG-2 is best to use oil. This type of lubricant relatively thin, more suitable for winter use; in summer, it is best to use the number ZG-4 grease. This type of lubricating oil more viscous, more suitable for summer use.

Portable Cutting Machine should be cleaned

First, wash and clean-up. As a steel processing equipment, steel cutting machine using undoubtedly will leave some residual steel scrap, so after using the need to develop a good habit, it is timely for the various machines are devices to clean up. So as not to be disturbed in the future use of the process. At the same time when the device is not used to carry out the necessary cleanup is particularly important, including the use of necessary damp cloth with neutral detergent to clean the surface of the device, remove stains and dirt on top of the machine, to avoid the prolonged impact of Portable Cutting Machine appearance and performance. In the clean-up time, especially for the interior of the machine and a number of blind spots clean.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check  Portable Cutting Machine is a regular process that requires a dedicated time to maintenance. The machine should be cleaned

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter:     The characteristic  GQ40A Rebar Cutter , which clearly shows us its automatic control at work, saving time and effort simply do not tell...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: The interior design GQ40A Rebar Cutter:     The characteristic  GQ40A Rebar Cutter , which clearly shows us its automatic control at work, saving time and effort simply do not tell...

The interior design GQ40A Rebar Cutter

    The characteristic GQ40A Rebar Cutter, which clearly shows us its automatic control at work, saving time and effort simply do not tell the length of its press wheels do not need to enter the number of pulses, it's excellent performance is reflected in this When the automatic identification and automatic integration of professional work.
    In addition, the interior design can reach the safe operation of GQ40A Rebar Cutter, wherein the interior of the electrical board, more than a layer designed to prevent dust or the conductive material to achieve fall into the danger of accidents caused by accidental short circuit. And this machine does not need frequent repairs, even when the repair is also very convenient. Of course, it's another laudable feature is its output more than one point, the general GQ40A Rebar Cutter will be arranged to three, this advantage is capable of preventing an unexpected point of failure occurs, change to another point in time work .

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ40A Rebar Cutter have the advantage?

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ40A Rebar Cutter have the advantage?:      First, the overall structure of the machine, whether it is the individual parts of  GQ40A Rebar Cutter or in the details of control ha...

GQ40A Rebar Cutter have the advantage?

     First, the overall structure of the machine, whether it is the individual parts of GQ40A Rebar Cutteror in the details of control have better control, cohesion and cutting device disposed between the power plant has a new and improved, fully in the design on the inside of the machine is optimized, so compared to the same type of machine, steel cutting machine structure more compact, the space occupied by smaller and more convenient for ordinary use and storage of the machine.
Followed by the processing performance of the machine, as the steel processing tools, you first need to meet the dynamic performance of the machine, GQ40A Rebar Cutter has a powerful motor and power systems as bedding, so the processing time can be reinforced to provide adequate power . There is also a big advantage is that the motor at the time of processing more small noise, the environment is a good lay.
     Finally, the material properties of the device, the various components of steel cutting machine uses the finest materials as a basis, whether processed or foil portion of the body part are used special strength of steel. Not only allow the device to be more hostile environment, while improving the overall quality and reliability of the equipment, the special paint coating to enhance the performance of the device.
     Works GQ40A Rebar Cutter incorporates new technology and design, so the device when in use need to follow the appropriate procedures and the operation sequence. From the user's point of view, excellent dynamic performance and a variety of user-friendly design to increase the use of chips to use numerous devices, is the ideal choice for everyone.

Portable Cutting Machine Uses

Portable Cutting Machine can be used for housing construction, bridges, tunnels, power plants, large-scale water conservancy projects for steel and Cutting. Mainly used to cut off the building with steel bars, round steel, steel bars, screw and so on.
The difference between the portable steel cutting machine cutting machine with ordinary
Portable steel cutting machine compared with other cutting devices, light weight, low energy consumption, reliable operation, high efficiency, so in recent years gradually been widely used machining and small rolling mills, etc., in various fields of national economy played an important role.
Portable Cutting Machine is introduced:
Portable electric hydraulic steel cutting machine comprising RC-16, RC-20, RC-22, RC-25 and a series of models. Light weight portable cutting machine, small size, easy to carry easy to operate, cutting process does not produce sparks, dust, no odor, is environmentally friendly machine tools.
Part of the manual hydraulic steel cutter
Hydraulic System manual hydraulic steel cutting machine by the piston, the piston, cylinder, lever, pull the pin, the return spring, storage drums and release, suction valves and other components.
Manual hydraulic steel cutting machine works
First release valve in a clockwise direction and tighten, lift lever plunger that is enhanced suction valve is opened, the hydraulic oil into the oil chamber; lift lever, the hydraulic oil into the cylinder chamber is compressed, thus pushing the piston forward , the moving knife mounted on the front end of the piston can be broken material. Immediately after blanking open valve counter-clockwise rotation, in return spring, oil has to flow back pressure oil chamber,Portable Cutting Machine will automatically retract cylinder. Again and again, were cut tendons.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: It requires the development of future GQ40A Rebar ...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: It requires the development of future GQ40A Rebar ...:   Prospects  GQ40A Rebar Cutter  is very good, mainly because the market demand for large, small competition, so the whole market is still...

It requires the development of future GQ40A Rebar Cutter

  Prospects GQ40A Rebar Cutter is very good, mainly because the market demand for large, small competition, so the whole market is still very good. With the economic development, the future needs of steel cutting machine will further increase, which is necessary to meet the market demand for. It is mainly in such aspects:
First, the market demand, because this device it is currently one of the most advanced equipment, many companies are upgrading, accelerate its replacement, because steel cutting machine can make up for many deficiencies, greatly increasing the efficiency of the work.
Second, the global warming economy, the domestic market is very active in foreign markets is also thriving scene appears, which is very good.
  In a conventionalGQ40A Rebar Cutter development, there is a great shortage lies not withstand excessive load, but not all aspects of the design is very reasonable, most are processed by hand, the price is relatively high, relatively poor performance does not meet the Modern society needs, so the traditional cutting machine or application is not stopped, as it has no market. Now pursue paint spraying, color is very scientific, appearance do not see weld gap and sharp corners, etc., it is very smooth and clean, beautiful, well received by customers like.
  GQ40A Rebar Cutter is a good development, it can be said the rapid economic development is inseparable from the future application of steel cutting machine, especially in great demand in the construction sector. With advances in technology, processes steel cutting machine is also rising, produced by the steel cutting machine has also been greatly improved, can be said to be very good, I believe the future will be better development.

How to make Portable cutting machine cutting precision minimized?

       Before examining factors Portable Cutting Machine cutting precision, we need to briefly explain the working principle of steel cutting machine, which is by the motor via a belt drive growth, make high-speed rotation tune straight through the transfer will be transferred straight steel straight, straight mold remove rust by steel surface of the skin, then motor through another pair of belts and gear box reduction effect, while you can drive two transport roller, traction bars forward movement, while you can crank wheel drive so that the hammer up and down motion.
       This process, when the reinforcing bars until a predetermined length, hammer hammering on the turret, steel can be successfully cut. In order to be able to complete the cycle when the device action,Portable Cutting Machine falls by rack, since the spring action, knife sets general will return to its original position. This is the basic workflow steel cutting machine, then the impact of steel cutting machine cutting precision of factors?
       First, the base material of different materials steel is the most fundamental factors for Portable Cutting Machine equipment, even the same material, if the composition of the material of different cutting accuracy will vary. Second, the impact of different diameter steel base material size on the cutting accuracy can not be ignored, because of different diameter steel cutting precision allowed deviation is completely different.
       In addition, different construction sites require precision steel processing will be different, which is also one of the steel cutting machine cutting precision factor. In fact, when the actual control of the operator of such equipment, the effect of skilled staff work between employees and unskilled will have a very significant difference, which directly relates to the steel cutting function achieve what cutting accuracy.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ42 Rod Cutting Machine formal method of operatio...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ42 Rod Cutting Machine formal method of operatio...: Before using the first  GQ42 Rod Cutting Machine  must be sure the work surface and the cutter is not kept below the level of the state, if...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ42 Rod Cutting Machine formal method of operatio...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: GQ42 Rod Cutting Machine formal method of operatio...: Before using the first  GQ42 Rod Cutting Machine  must be sure the work surface and the cutter is not kept below the level of the state, if...

GQ42 Rod Cutting Machine formal method of operation

Before using the first GQ42 Rod Cutting Machine must be sure the work surface and the cutter is not kept below the level of the state, if not, the first thing to do is to adjust the level, then check the cutter steel cutter There are no abnormal phenomenon, for example, there is no crack crack, screw fastening tool is not, but also turned by hand at the pulley, check the top of the backlash is not appropriate, and if we find inappropriate, first adjust better.
Plug in the power, the start time, do not worry now operating on steel, should first dry run for a while, take a look at every part of the operation is not a normal steel cutting machine, to determine a good no anomalies, then you can really start operate. In the cut material time, pay more attention to the correctness of the staff is a hand operation, and posture on. Middle and lower use of GQ40A Rebar Cutter should cutter, hand grip bars to the staff, and aligning the entrance of the cutter. If you are a person to operate it, the staff must be fixed position, can only stand on the side of the blade and hard pressed steel, in the course of their work should not arbitrarily change position, to avoid wounding steel.
If GQ42 Rod Cutting Machine can not be more than a one-time cut rebar, then do not do it abruptly, range of different steel cutting machine has a work must be able to ensure the safety of staff inside the operating range.

Portable cutting machine, the need for construction industry equipment

What is Portable Cutting Machine? In fact, it is cutting equipment, primarily for cutting steel, meets the requirements of the job. Many people do not understand the cutting machine steel, because life is not common, which is generally used in the construction industry, especially the demolition of houses, often used for machine equipment steel cutting . Here we look at the role of steel cutting machine in the construction industry?

I. cutting rebar to cut
   In the construction sector, steel is a material commonly used, however, requires the use of steel cutting machine, mainly in the demolition and other work. It reinforced in the home will be a design far the demolition of the time, the use of other tools can not strengthen the open, requiring cutting machine for cutting, in order to comply better job of demolishing houses .

   In addition to demolish the houses and some other areas also they need Portable Cutting Machine. Rod used mowers not only cut, but also applied to cut other hard materials, widely seen cutting applications the machine can be used to meet their needs in different fields.

II. To accelerate productivity
   For Portable Cutting Machine, the acceleration efficiency is the biggest advantage. Because in some jobs, if attention to the work of the steel cutting machine is not paid, will increase work efficiency.

GW40B Manual Bending Machine

GW40B Manual Bending Machine

GWH-32 Rebar Radius Bending Machine

GWH-32 Rebar Radius Bending Machine

GQ52 Rod Cutting Machine

GQ52 Rod Cutting Machine

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter

C42 Rebar Cutter
Introduction:
C42 rebar cutter can be applied to cut plain carbon steel, hot rolled round steel, deformed steel bar, flat steel, square steel and angle steel, etc. As a professional steel bar cutter manufacturer in China, our C42 electric rebar cutting machine is widely used in construction sites and steel bar processing factories.
Why Choose our Rebar Cutter?
Specifications of C42 rebar cutter:
Item C42
Cutting Capacity ≤Φ42mm
Cutting Frequency 90revs/min
Motor Power 3KW-3phase
Voltage 380V
Weight 550kg
Dimension(L×W×H)(mm) 1220×570×650
Pre-sales service:
1. Foreign customers are welcome to visit our factory for free.
2. Customize special C42 electric rebar cutting machine as per customers’ demands for free.
3. Provide manual in Chinese, English, Spanish, Portuguese, French, Arabic, Russian and Thai for special products.
In-sales service:
1. Provide technical support for customers on machine operation to ensure they can operate correctly.
2. Supply wearing parts for free and we are responsible for inland freight cost.
3. Delivery time of domestic orders: 1to 3 days.
4. Delivery time of overseas orders: 5 to 15 days.
After-sales service:
1. 24 hours after-sales technical support for free.
2. Provide one year quality warranty for C42 Rebar Cutter.
3. Replace damaged parts of quality problem within the quality warranty period.
Other special services:
1. For inland and Thailand customers, we can offer on-site installation and guidance. For overseas customers, we can provide training for free. For customers in other countries, we provide third-party agent support.
2. We can customize C42 electric rebar cutting machine.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter

C42 rebar cutter can be applied to cut plain carbon steel, hot rolled round steel, deformed steel bar, flat steel, square steel and angle steel, etc. As a professional steel bar cutter manufacturer in China, our C42 electric rebar cutting machine is widely used in construction sites and steel bar processing factories.
Why Choose our Rebar Cutter?
1. Foreign customers are welcome to visit our factory for free. 
2. Customize special C42 electric rebar cutting machine as per customers’ demands for free. 
3. Provide manual in Chinese, English, Spanish, Portuguese, French, Arabic, Russian and Thai for special products.

In-sales service:

1. Provide technical support for customers on machine operation to ensure they can operate correctly. 
2. Supply wearing parts for free and we are responsible for inland freight cost. 
3. Delivery time of domestic orders: 1to 3 days. 
4. Delivery time of overseas orders: 5 to 15 days.

After-sales service:

. 24 hours after-sales technical support for free. 
2. Provide one year quality warranty for C42 rebar cutter. 
3. Replace damaged parts of quality problem within the quality warranty period.

Other special services:

1. For inland and Thailand customers, we can offer on-site installation and guidance. For overseas customers, we can provide training for free. For customers in other countries, we provide third-party agent support. 
2. We can customize C42 electric rebar cutting machine.

GQ40A Rebar Cutter

GQ40A Rebar Cutter

GW32 Automatic Bending Machine

GW32 Automatic Bending Machine

rebar cutting machine

rebar cutting machine

GW40B Manual Bending Machine,Portable Cutting Machine

GW40B Manual Bending Machine

GWH-32 Rebar Radius Bending Machine

GWH-32 Rebar Radius Bending Machine

Rebar Cutter

Rebar Cutter

RC-16 Portable Cutting Machine

RC-16 Portable Cutting Machine

GW40B Manual Bending Machine

GW40B Manual Bending Machine

Semi-automatic cutting machine

Semi-automatic cutting machine

VID 20141115 104904

(Portable cutting machine, C42 steel cutting machine, GQ40A steel cutting machine) Features

Portable Cutting Machine Features: Suitable for all kinds of construction works on ordinary carbon steel, hot rolled round bar, rebar, cut flat steel, square steel. Off round: (Q256-A) Diameter: (Φ6-Φ40) mm, cut flat maximum size: (70x15) mm, cut square steel: (Q235-A) maximum size: (32x32) mm, maximum cutting angle specifications : (50x50) mm. C42 steel cutting machine features: generally have automatic steel cutting machine, steel cutting machine and semi-divided. Automatic cutting machine is also known as electric energy into kinetic energy through the motor control cutter cuts, to achieve the effect of shear reinforcement. The semi-automatic manual control incision is so cut steel operations. At present, more is GQ40A steel cutting machine.

(Portable cutting machine, C42 steel cutting machine, GQ40A steel cutting machine) applications

Portable Cutting Machine is a tool used by a shear reinforcement. Generally C42 steel cutting machine, steel cutting machine and semi-points, it is one of the indispensable steel processing equipment. Portable cutting machine is mainly used for housing construction, bridges, tunnels, power plants, large-scale water conservancy projects for steel and Cutting. GQ40A steel cutting machine compared with other cutting equipment, light weight, low energy consumption, reliable operation, high efficiency, it has been widely used in recent years gradually machining and small rolling mills, etc., in all areas of the national economy played a important role.

The practical application of C42 steel cutting machine and semi GQ40A steel cutting machine

Portable cutting machine technology, is a safe "cold" cutting technology, not because of sparks caused by gas explosion. To meet the needs of the coal mine of the cutting operation, the design and manufacture of portable coal mine abrasive water jet cutting machine. device body divided into two parts with a high pressure hose connection, workers operating a handheld gun cut cutting operation, cutting speeds up to 40mm / min; C42 steel cutting machine can be monitored by a pressure gauge system pressure, nozzle wear, abrasive dosage index , GQ40A using steel cutting machine equipment to achieve the safety of coal mine operations were cut.